MECHANICAL SOLUTIONS

CERAMIC WEAR PROTECTION

Anti-abrasion and anti-erosion coatings for cement mills

FOR SELECTED DUTIES BELOW 120°C

01  CERAMIC PRIMER

1180 NMB Ceramic Coat

FLEXIBLE PRIMER · ST3 GRINDING

Nano Molecular Bonding (NMB) anchors 1180 to
ST3-ground steel without abrasive blasting for
specified applications. The flexible ceramic primer
resists brittle cracking and peeling, helping keep
the full system bonded.

02  CERAMIC WEAR LAYER

731 ER XTREAM

NANO ZIRCONIUM WEAR RESISTANCE

This fibre-reinforced putty uniquely uses hard
nano zirconium for substantially better abrasion
and erosion resistance than conventional
ceramic-bead or standard zirconium coatings.
Higher coverage per kg reduces coating
consumption.

CEMENT MILLS

Standalone grinding units and integrated cement plants

Cement plant with storage silos, preheater tower and conveyor gallery

Illustrative problem and after views

01–05  Grinding & integrated   ·   06  Integrated coal preparation

Cement dust scours out grout and exposes the separator tile edges.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

CEMENT DUST SCOURS OUT GROUT AND EXPOSES
THE SEPARATOR TILE EDGES.

01

Finish-Mill Separator Linings

APPLICATION

Worn joints, tile edges and approved local wear zones
in cement separator cones and casings.

TECHNOLOGY

1180 primes the compatible prepared surface. 731
ER XTREAM fills local wear and fairs the transition to
sound lining.

CUSTOMER GAIN

Keep sound lining in service longer and reduce the
amount of relining at shutdown.

Fine cement dust scours the leading edges and faces of fixed guide vanes.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

FINE CEMENT DUST SCOURS THE LEADING EDGES
AND FACES OF FIXED GUIDE VANES.

02  ·  SITE TRIAL

Finish-Mill Separator Guide Vanes

APPLICATION

Local wear on stationary guide vanes in finish-mill air
separators.

TECHNOLOGY

1180 primes the prepared steel. 731 ER XTREAM
rebuilds worn edges and faces to the original profile.
Maintain vane angle and spacing.

CUSTOMER GAIN

Help preserve airflow through the separator and
extend guide vane life.

Cement powder cuts grooves into the diverter body where the flow turns.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

CEMENT POWDER CUTS GROOVES INTO THE
DIVERTER BODY WHERE THE FLOW TURNS.

03

Powder Lines & Diverter Bodies

APPLICATION

Dry cement and fly-ash line elbows, plus local wear
inside powder diverter bodies.

TECHNOLOGY

1180 primes the metal. 731 ER XTREAM rebuilds
worn pockets and protects the surfaces struck by the
powder stream.

CUSTOMER GAIN

Help retain flow geometry and reduce repeated pipe
and valve-body replacement.

Fine powder wears a groove in the mill shell behind the lifting liner.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

FINE POWDER WEARS A GROOVE IN THE MILL SHELL
BEHIND THE LIFTING LINER.

04

Tube-Mill Shell Under Lifters

APPLICATION

Worn backing surfaces beneath steel lifting liners in
tube-mill pre-drying chambers.

TECHNOLOGY

1180 primes the exposed shell. 731 ER XTREAM
rebuilds local loss to the specified support profile
before the liner is refitted.

CUSTOMER GAIN

Restore the seating surface and protect the shell
during the next liner service cycle.

Dust erodes impeller edges, changing the blade profile.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

DUST ERODES IMPELLER EDGES, CHANGING THE
BLADE PROFILE.

05

Cement Dust Fan Impeller Edges

APPLICATION

Local leading-edge wear on cement dust extraction
impellers, after part assessment.

TECHNOLOGY

1180 primes the prepared edge. 731 ER XTREAM
restores the approved profile. Check clearances and
balance before restart.

CUSTOMER GAIN

Help retain blade profile and reduce repeated rotor
repair or replacement.

High-velocity coal fines scour the cyclone wall and outlet.Illustrative after view: the worn area rebuilt and protected with 1180 + 731 ER XTREAMAFTER

HIGH-VELOCITY COAL FINES SCOUR THE CYCLONE
WALL AND OUTLET.

06  ·  INTEGRATED PLANTS

Coal Cyclones & Outlet Pipes

APPLICATION

Coal-preparation cyclone inlets, wall wear zones and
connecting pipes at integrated cement plants.

TECHNOLOGY

1180 primes the substrate. 731 ER XTREAM forms a
nano zirconium wear layer at coal-dust impingement
points.

CUSTOMER GAIN

Slow local thinning and protect the cyclone profile
between inspections.

Confirm the peak metal temperature, substrate condition and particle or slurry duty before specification. Use the approved
wet-service temperature and chemistry for immersed parts.

STANVAC CHEMICALS INDIA LTD.

Home Download